|
|
|
Ball Joint Separator
(KD2287) Ball Joint SeparatorFeatures: Tool separates ball joints from steering knuckles. To use, insert 15/16"" opening between parts and strike with hammer. Separator is forged to withstand hard usage. Overall length: 12""
Sale price: $17.45
See it at Closeout.com.
|
|
|
|
|
Ball Joint Press with 4WD Adapters
(AP7865) Ball Joint Press with 4WD AdaptersFeatures: Ball joint service Universal joint service Truck brake anchor pin service Four wheel drive ball joint service Will remove even rusted and corroded parts Includes: C-Frame press, 3 Receiver tubes (2-3/4""I.D.x3""O.D., 2-1/4""I.D.x2-1/2""O.D. and 1-3/4""I.D.x2""O.D.), 1 Installing adapter, 1 Removing adapter, 1 Installing cup, 1 Receiving cup
Sale price: $73.21
See it at Closeout.com.
|
|
|
Honda Lower Ball Joint Service Set
(OTC7996) Honda Lower Ball Joint Service SetFeatures: Used with OTC 7249 ball joint service set to remove/install both sizes of ball joints on 1983-1997 Honda Accord, Civic, del Sol and Prelude. 4 piece set.
Sale price: $94.16
See it at Closeout.com.
|
|
|
Ball Joint Spanner Wrench
(OTC7080) Ball Joint Spanner WrenchFeatures: Designed for removal and installation of ball joint adjusting sleeves on 1/2-, 3/4-, and 1-ton Dana open yoke front axles found on Ford, GM, Chrysler, IHC and Jeep 4WD vehicles. Tool permits easy torquing with 1"" socket for proper upper ball joint preload. Same as Ford No. T71T-3010-G
Sale price: $20.64
See it at Closeout.com.
|
|
|
Greasable Ball Joints
GREASABLE BALL JOINTS Solves the problem of replacing lost grease Replace non-greasable original-equipment ball joints For '62-95 4WD pickups and SUVs Easy-to-service joints survive off-road abuse. Can be lubricated on a routine maintenance schedule to prolong life and increase durability. Available for upper or lower ball joints.
Sale price: $18.99
See it at JC Whitney.
|
|
|
Ford E250/350 Van Ball Joint Remover
(OTC7825) Ford E250/350 Van Ball Joint RemoverFeatures: When used with OTC7249 ball joint service tool set, lets you quickly remove the lower ball hoint on 1992 and newer 3/4- and 1-ton full-size vans (E-250 and E-350)
Sale price: $61.86
See it at Closeout.com.
|
|
|
Ball Joint Separator Fork
(OTC6535) Ball Joint Separator ForkFeatures: Used to remove shock linkage, tie rods, and ball joints. Also for general service on many cars and light trucks. Size: 16"" long, 15/16"" Fork Spread
Sale price: $19.93
See it at Closeout.com.
|
|
|
Ball Joint Service Tool Set
(OTC7249) Ball Joint Service Tool SetFeatures: This set removes and replaces ball joints. The C-frame press alone can also be used to remove and replace universal joints. Includes: C-frame press, receiver tube (3"" O.D. x 2-3/4"" I.D.), receiver tube (2-1/2"" O.D. x 2-1/4"" I.D.), receiver tube (2"" O.D. x 1-3/4"" I.D.), installing adapter, removing adapter, carrying case.
Sale price: $90.29
See it at Closeout.com.
|
|
|
Master Ball Joint Adapter Set
(OTC7918) Master Ball Joint Adapter SetFeatures: This set was created specifically to expand the capability of your OTC7249 ball joint service tool set. It includes all the receiver tubes and removing/installing adapters needed to work on press-fit upper and lower ball joints on most GM, Ford, and Dodge, 2 and 4-wheel-drive pickups, vans, and sport utility vehicles, through 1997. Also includes the No. 7917 live center forcing screw plug. Packaged in a convenient carrying case and includes application chart.
Sale price: $237.35
See it at Closeout.com.
|
|
|
Ball Joint Remover/Installer Super Set
(OTC6530) Ball Joint Remover/Installer Super SetFeatures: This set allows for the removal and installation of press-fit ball joints on many GM and Ford light-duty trucks, vans and SUVs through 2003; Dodge light trucks through 1998; Dodge vans, Durango and Dakota through 2003; and Honda Accord, Civic, del Sol, and Prelude through 2001. Combines the popular OTC 7249, 7918 and 7996 ball joint sets into one SUPER set, competitively priced. The OTC designed and produced C-frame tool can be used alone to remove and replace universal joints. Comes complete with an application cross reference and instructions in a blow-molded case.
Sale price: $270.91
See it at Closeout.com.
|
|
|
Ball Joint Separator-
"BALL JOINT SEPARATOR Made of drop-forged alloy steel, heat-treated for long and rough use Tapered wedge with 15/16"""" jaw opening slides between ball joint and steering knuckle Professional-quality, hand-held tool specially designed for front-end work 11-7/8""""L. Knurled for secure grip. Fast and easy. Just hit tool with hammer to force wedge between parts."
Sale price: $8.49
See it at JC Whitney.
|
|
